Making a Floating Shelf with "Wave" shape using Fusion 360 and CNC (or with standard Woodworking tools)

This video shows how to make modern DIY floating shelves using easy woodworking or a CNC. This floating shelf was made from three 2'x4' plywood sheets. I'm going to be using these DIY modern shelves as small parts storage in my workshop. This is about as close to making a shop project as you'll see :)

The video shows not only how to make a modern floating wave shelf, but also how to use parametric design in Fusion 360 to create all kinds of cool parametric furniture and designs. Specifically, I used the Slicer plug-in for Fusion 360,allows you to take 3D models and slice them into 2D shapes that snap together. The software also will automatically create 2D templates of the pieces, so that you can cut them out with a jigsaw or bandsaw, making this a simple woodworking project. Or you can cut it out of the 1/2" plywood on your X-Carve CNC using the Easel project I created (link below).

PDF PLANS / TEMPLATE: http://bit.ly/mm_waveshelf

EASEL PROJECT FOR SHELVES: http://bit.ly/2FpVua5

Sign up for a FREE EASEL account: https://www.inventables.com/technologies/easel?ref=modustrial

Inventables X-CARVE CNC: https://www.inventables.com/technologies/x-carve?ref=modustrial

To see some people taking this type of parametric design to the next level, who I was inspired by, check these folks out:

- Harrington Design: @harrington_design_co

- P.Metric: @parametric.arch

\\TOOLS//

double sided carpet tape: https://amzn.to/2UQL096

glue sticks: https://amzn.to/2ULn3jp

one-and-done spray paint: https://amzn.to/2ugmd2o

Jigsaw: https://amzn.to/2UI4IUo

Cordless Track Saw: https://amzn.to/2LuE6EV

Table Saw: https://amzn.to/2A4tQP9

\\ FOLLOW ME//

INSTAGRAM - @modustrialmaker - https://goo.gl/F4UdEs

BLOG - www.modustrialmaker.com

NEW VIDEO is Up! BLUETOOTH BOOMBOX made from recycled SKATEBOARDS -- check it out! →

In this video, I show how to make a portable bluetooth boombox from twice recycled skateboard wood.  I managed to use every part of the skateboard in this DIY speaker build. The front panel is formed from reclaimed skateboard wood, the handle of the speaker is made from skateboard trucks, and the feet are made from skateboard wheels and bearings.  

I used Dayton Audio kit parts for the electronics.  It has a 2x50w Bluetooth amp, which is driving two Tang Band 5” W5-2143 full range speaker drivers.  It is battery powered, with great battery life, and most importantly, sounds amazing!  

A huge shout out to KIRBY MEETS AUDIO for his help in designing the speaker enclosure and selecting the Tang Band drivers.  His channel has a wealth of information on speaker design and speaker building, and his video production is top notch.  Go subscribe to Kirby Meets Audio if you haven’t already!
KIRBY MEETS AUDIO YOUTUBE CHANNEL: https://goo.gl/8gFxnw
Also, a big thanks to FOCUSED SKATEBOARD WOODWORKS for sending me their offcuts and making this build possible.  Check them out!
Web: https://goo.gl/tM4T2s
Instagram: @focused_skateboard_woodworks

SPEAKER PARTS USED IN BUILD

• Bluetooth Amplifier Board: https://goo.gl/UgQ4wq
• 5” Full-Range Drivers: https://goo.gl/4WXUtJ
• Battery Charger Board: https://goo.gl/1w3C74
• Li-ion Batteries: https://goo.gl/LUPbzs
• 19V Power Supply: https://goo.gl/t2sZwB
• “L” Brackets for Amp and Battery Boards: https://goo.gl/SQzwwQ
• Cable Kit (on/off. Volume, line input): https://goo.gl/XY6gcy
• 2.5” Ports: https://goo.gl/mQwhL2

TOOLS FOR ELECTRONICS
• My favorite solder: http://amzn.to/2CNgjIF
• Quality Soldering Iron: http://amzn.to/2CKHoMC
• Blue Soldering Mat: http://amzn.to/2DboPCd

WOODWORKING TOOLS
• Cordless Nailer: http://amzn.to/2FJIsFW
• Ridgid Cordless Router: http://amzn.to/2pinfZL
• 90 Degree driver / oscillating saw: http://amzn.to/2FHqrbB
• Hole Saw Kit: http://amzn.to/2GztkIw
• RZ dust mask: http://amzn.to/2wM8F1t
• Bosch 18V cordless circular saw: http://amzn.to/2wcDgnN
• Bosch 18V cordless Drill & Impact Driver Kit: http://amzn.to/2BCI753
• Dewalt Table Saw w/ 32” Rip Capacity: http://amzn.to/2yQd2Fy
• Japanese Flush Cut Hand Saw: http://amzn.to/2yRa1Fd
• Dewalt 12” Miter Saw: http://amzn.to/2yQRgS6
• Forstner Bits: http://amzn.to/2Bgv863

FOLLOW ME ON INSTAGRAM: @modustrialmaker || https://goo.gl/3Yqo2m 

For those interested in building one of these, here are the calculations for the Tang Band 5" speakers and 2.5" ports.  The below shows the enclosure for a single speaker -- for the boombox, you'll have two enclosures; one for each speaker.

NEW VIDEO! Making a "LIVING ART" LED Desk LAMP

In this video I show how to make a Modustrial-designed DIY “Living Art” LED lamp from plywood and an LED matrix.  

The LEDs in the lamp are controlled by an Arduino Nano that creates colorful moving patterns, aka, “living art.”  However, it is also very practical for use as a desk lamp, table lamp, or bedside lamp, since an LED push button allows you to switch from the living-art mode to normal white-light modes, and a red-nightlight mode.   

I made three versions of this lamp – two out of bamboo plywood, and one out of walnut plywood.  You could use any type of plywood you like to build the lamp.

The electronics were designed to be very simple.  It can be built with NO SOLDERING.

To see the finished walnut version of the lamp, FOLLOW ME ON INSTAGRAM: https://www.instagram.com/modustrialmaker/  || @modustrialmaker

PARTS FOR THE BUILD:

• 16x16 LED Matrix: http://amzn.to/2BgIcsj
• Arduino Nano: (pre-soldered) http://amzn.to/2H0h6bS
• Arduino Nano Screw Terminal Shield: http://amzn.to/2FZwy6y (pre-soldered)
• 5V Momentary LED push button: http://amzn.to/2CLbu2E OR https://goo.gl/Cn1iDy
• JST Connectors: http://amzn.to/2ALve4j
• Semi-transparent white acrylic sheet: https://goo.gl/YV4X81
• Female Power Jack: http://amzn.to/2H3oN0P (no solder) || http://amzn.to/2ziyuEB (solder)
• Lever-nut Wire Connectors: http://amzn.to/2BhMtvM
• 5V power supply: http://amzn.to/2zgiGSJ

ARDUINO NANO CODE FOR THE LAMP: https://github.com/modustrialmaker/Living_Art_LED_Matrix_Lamp

ELECTRONICS TOOLS

• My favorite solder: http://amzn.to/2CNgjIF
• Quality Soldering Iron: http://amzn.to/2CKHoMC
• Blue Soldering Mat: http://amzn.to/2DboPCd

OTHER TOOLS I USE:

• Tap Drill Bit (for threaded holes): http://amzn.to/2Fm7V4A
• RZ dust mask: http://amzn.to/2wM8F1t
• Bosch 18V cordless circular saw: http://amzn.to/2wcDgnN
• Bosch 18V cordless Drill & Impact Driver Kit: http://amzn.to/2BCI753
• Dewalt Table Saw w/ 32” Rip Capacity: http://amzn.to/2yQd2Fy
• Japanese Flush Cut Hand Saw: http://amzn.to/2yRa1Fd
• Dewalt 12” Miter Saw: http://amzn.to/2yQRgS6
• Forstner Bits: http://amzn.to/2Bgv863

Making a Waterfall Countertop with LED River Inlay || DIY Concrete (GFRC) || Mancave Makeover Ep. 1

New build video is up on my YouTube channel.  This video explains how to make a one-piece DIY concrete waterfall countertop with an inlaid river of flowing LEDs that cascades over the waterfall edge (using neopixel LED strips).   

This is the first of two videos for a mancave makeover at a friend's house.  Part 2 will be uploaded within the next week, and will show how to make and install a reclaimed wood feature wall with floating LED TV panel, and the installation of the cabinets.

The countertop is made from a glass-fiber reinforced concrete (GFRC) concrete mix, which is pre-cast in a melamine form.  I made the mix from scratch (recipe links are below).  I mixed 280 lbs of the dry materials (including powdered pigment) all at once, so the color would be consistent.  I used 40 lbs for the face coat, and the remaining in batches for the back coat with glass fibers.

I used an off-the-shelf LED controller that has MUSIC REACTIVE modes, chasing modes, and solid color modes, with an RF remote, to control the WS2812 LED strips.  The LEDs are covered by a smoke grey transparent acrylic sheet, which is inlaid so it sits flush with the concrete countertop.

MM-Inspired Build - Chris Gagnon's DIY Pendant Double-Ring Light

Chris Gagnon shared a video documenting the build process for a double ring light, which he indicates was inspired by Rings of Saturn light.  I think it came out pretty cool - well done Chris!

Here is what Chris said about the project: 

“I wanted to put my own twist on it by using segmentation. I have always been interested in wood segmentation and the projects that you can make with it. This project is inexpensive and requires very little tools. All your friends will be so impressed when you start making things using this new skill you are gonna learn here. One thing I want you to take away from this video is that you don’t need to spend hours building a fancy jig for your table saw to do perfect segmentation projects and I am going to show you how right now. so lets get started.”

And, in case you haven't seen it, check out the original video for my Rings of Saturn light.

How to Turn Concrete into MARBLE -- new Table Build Video is Up!

New Build video is up! In this video I show how to make a DIY concrete coffee table top look like marble.  The top is made using Fishstone’s glass fiber reinforced concrete (GFRC) ready-made concrete mix, which is pre-cast in a melamine form.  I separated out batches of different colored concrete (from white to dark grey), mixed them together in the form, and then swirled them together by hand to get the marble-like appearance.

I also used an ancient Japanese technique called “Shou Sugi Ban” to make the base for the coffee table.  I used a modernized version of shou sugi ban, employing a propane torch to char the outside of the wood.  The charred wood is natural way of protecting the rest of the wood, and when finished with a penetrating oil, such as Danish oil, provides a durable surface.  This technique works well on any open-grained wood, such as Douglas fir, pine, and cedar.  I used inexpensive 4x4 Douglas fir lumber from my local big box store.  

CONCRETE (GFRC) PRODUCTS USED: 

• Two bags of Pre-Blended GFRC Mix: https://goo.gl/izSggQ
• 1.5 Bag of AR Glass Fibers: https://goo.gl/c9Vw9x
• Cake Fondant Tool for perfect edges: http://amzn.to/2w0JCVx
• Concrete mixer (HUGE help for GFRC): http://amzn.to/2kEnZFi
• StoneTech concrete sealer: http://amzn.to/2gSrjyp
• Another concrete sealer I like: http://amzn.to/2xW7Gth
• Black 100% Silicone Caulk: http://amzn.to/2B64iRY
• Paste Finishing Wax: http://amzn.to/2kF565e
• Concrete Pigment: http://amzn.to/2yPo51P

WOOD

 - Three (3) 8 ft. 4x4s -- Douglas Fir, Cedar, or Pine
 - 3/4" Dowels: http://amzn.to/2yTWrkl

OTHER PRODUCTS USED IN VIDEO:

- Propane Torch: http://amzn.to/2yQbtaV
- Danish Oil: http://amzn.to/2yRhlAw
- RZ dust mask: http://amzn.to/2wM8F1t
- Diamond Grinding Wheel (for grinding underside of table): http://amzn.to/2yRL6RY
- Forstner Bit Set: http://amzn.to/2yQAoej
- Tack Life Level: http://amzn.to/2yQhYuk
- Kreg Pocket Hole Jig: http://amzn.to/2kCvlsW
- Herzo Dust Shround for Angle Grinder: http://amzn.to/2yPymLr
- 

TOOLS I USE:

- Tack Life Angle Grinder: http://amzn.to/2B6fwWG
- Bosch 18V cordless circular saw: http://amzn.to/2wcDgnN
- Bosch 18V cordless Drill & Impact Driver Kit: http://amzn.to/2BCI753
- Dewalt Table Saw w/ 32” Rip Capacity: http://amzn.to/2yQd2Fy
- Japanese Flush Cut Hand Saw: http://amzn.to/2yRa1Fd
- Dewalt 12” Miter Saw: http://amzn.to/2yQRgS6

MM-inspired Concrete and Live-Edge Inlay Charcuterie Board

The Cutting Bored just uploaded a video of their concrete and live-edge inlay charcuterie board.  (I'm trying to resist saying its a cutting board by the Cutting Bored :) ) The video indicates this board was inspired by my live-edge table build video, but this is really a unique twist on the design.  They used inexpensive materials and still got a great looking result.  

Generally, The Cutting Bored has a great YouTube channel going, so check out the rest of their videos as well, and show some love by subscribing.

For those that missed it, here is the original live-edge white concrete table that the Cutting Bored references in their video.

NEW BUILD VIDEO IS UP! DIY White Concrete (GFRC) Table with Live-Edge Maple Inlay

I just posted the build video for my white concrete table with live-edge inlay.  I really like how this project came out -- very simple and modern.  I will be updating my Modustrial Maker website with more details and plans soon.

DIY "Rings of Saturn" LED Pendant Light w/ Music Visualization Mode

I made this LED pendant light from plywood, LED strips, and flexible LED channel.  Since I designed this for my living room, the music syncing had to be incognito.  With this in mind, I used warm white / cool white / amber LED strips, instead of RGB strips.  In solid white mode, the rings give off various shades of white for a sophisticated modern look that hides the wild side when you switch the light to music visualizer mode.

The build is fairly simple.  Each of the two rings is made of a stack of three plywood rings, where the middle ring has a lesser radius to create a groove for the LEDs.  The rings are simple to cut using a circle cutting jig and router.  While I programmed an Arduino Mega to do music visualization based on input from a microphone, you can very easily buy an off-the-shelf music controller for individually controllable LEDs, which is basically plug n’ play for the LED strips.